![]() train damage or unexpected vehicle movement which. Tip: You can search the list below for a Keyboard Shortcut by doing a Ctrl F and entering a word such as Ditch.Īlso, If you do not have Thrustmaster Compatible Controllers, you may want to try Joy to Key to map Joystick inputs to keyboard inputs - link below. For additional information, refer to Parking brake in the Starting and driving section of this manual. ![]() I also provided downloadable copies of the Train Sim World 3 PC Keyboard Shortcuts in RTF, and CSV format, + a listing and the screenshots below. Here are the Train Sim World 3 Locomotives PC Keyboard Shortcuts. If the PA system is active and your train is in passenger service, make an short announcement of the reason for the delay to passengers between steps 2 and 3.Because I had difficulty finding a list of keyboard shortcuts for TSW3 to keep on my second monitor as a reference, I produced this listing by hand. on the emergency brake rate of the train. If all these have failed, remember 1 - 2 -3:ġ) Contact the signalman and make him aware of your problemĢ) Contact control and make them aware of the problemģ) Contact the depot to ask for further advice Braking algorithm, enforcement algorithm, Positive Train Control, PTC, simulation, Monte. Wait for 90 psi in brake pipe, 140 psi in main reservoir. In a JustTrains 153, you also have to wait for the guard to ding-ding to tell you leave.ĭid you activate the emergency brake, or was it pre activated? Set the reverser to neutral, push the main brake handle as far as it will go so that the emergency brake is fully applied applied, release it and check that the brake pressure indicator shows that the brake is fully released, before pushing the reverser into forward, then trying to apply power using the throttle. Ive only tripped the PCS on the SD40, so Im not sure if its the same on the F7. Check the external camera and if the doors are open, wait for them to close. If the Traction Fault light illuminates, repeat the process. Wait for the brake pressure reading to come down to near 1, before applying throttle. Now set the Reverser to foward ( or backwards ) and move the brake lever from emergency to Initial setting. ![]() A cold and dark locomotive starts with no air in the brake pipe, so this must now be pressurised. The AWS alarm will sound, so press Q to reset. Check the MU-2A Valve and ensure it is set to Lead or Dead. Check the brake stand and ensure the Cut-Off Valve is set to Freight. Check that the handbrake is released, the independent brake is released, and the handbrake / parking brake is released.Īre you meant to be able to move? If the doors are open, some trains will have an interlock which prevents you from opening the doors. Turn on the Ditch Lights, Gauge Lights and set Headlights to bright. On some locomotives and trains, there are two or more brakes. ![]() Use your ears and check the RPM indicator in the Head-up-display bar at the bottom of the screen.Īre ALL the brakes FULLY released? Check the brake gage. The DSD is a repeated beeping sound, it's simply a vigilance device, or a dead man's switch to make sure the driver is paying attention, or hasn't passed. If the driver fails to acknowledge the warning within two seconds the emergency brakes will apply. Try pressing the AWS reset button for 5+ seconds, just in case there is a sound effect missing or something.Ĭheck the engine is running. The warning sound must be acknowledged by the driver by pressing the AWS reset button 'Q'. You are supposed to push it in when you are at a red signal or operating under caution while making station stops) Some models it can be hard to see. emergency braking demonstrator running in an industry-grade simulator. This problem doesnt happen in the other direction, it just annoys me its happening in this direction. Is the DRA activated? (this is the red light button on the dashboard. Hey all I have been playing the TGV route for a bit now and Ive encountered a problem when I change the pantograph from LGV to DC, driving in the direction of Marseille. Is the reverser in forward? Check that there is no an off position.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |